Repad Design Information

Temperature: The maximum mean metal design temperature for the reinforcing pad.

Repad Height/Length: Enter the height/length of the reinforcing pad (measured along the length of the shell).

Repad Width: Enter the width of the reinforcing pad (measured around the girth of the shell).

Repad Thickness: The thickness of the reinforcing pad.

Repad Weld Leg: The fillet weld leg between the repad and the host.

Material: A brief description of the component material. When the material selection dialog is used, the default description is based on settings on the Materials-Misc. tab under Tools > Defaults. For example, if the settings are for Spec and Type/Grade and the material is SA-516 Grade 70, this field will show SA-516 Gr. 70. If the settings are instead just for Spec, the field will show SA-516. The field may be edited by the user to say anything without breaking the relationship to the material database; while this flexibility can be very helpful, the user must take care to enter correct information.

Condition: A brief description of the component material. Similar to the "Material" field, the description will default a certain way based on settings on the Materials-Misc. tab under Tools > Defaults when the material selection is used. This field may be edited by the user without breaking the relationship to the material database. As with the “Material” field, the user must take care to enter correct information.

Density: The material density based on table PRD from Section II, Part D. For those materials that did not have a clear match in this table, every effort was made to assign conservative values. Manually editing this field will sever the connection to the material in the database as indicated by the "Unlisted Material" caption.

Stress (Hot): The material allowable stress at the repad temperature. When a 3.5:1 safety factor is specified in the vessel screen, this value comes from Section II, Part D (Table 1A for Ferrous Materials, Table 1B for Non-Ferrous Materials, and Table 3 for Bolting). If a 4:1 safety factor is specified, this value is calculated based on the ultimate strength from Table U in Section II, Part D; furthermore, the value is limited to the values listed in the allowable stress tables for yield and creep governed cases. In cases where the repad temperature exceeds the highest temperature entry for this material’s stress line, the value will be zero. Manually editing this field will inform the software that the user is defining the material differently than what is stored in the database and the connection to the material in the database will be severed. This is indicated by the “Unlisted Material” caption.

Stress (Cold): The material allowable stress at 70 °F (20 °C). When a 3.5:1 safety factor is specified in the vessel screen, this value comes from Section II, Part D (Table 1A for Ferrous Materials, Table 1B for Non-Ferrous Materials, and Table 3 for Bolting). If a 4:1 safety factor is specified, this value is calculated based on the ultimate strength from Table U in Section II, Part D; furthermore, the value is limited to the values listed in the allowable stress tables for yield and creep governed cases. Manually editing this field will sever the connection to the material in the database as indicated by the “Unlisted Material” caption.

Yield Strength: The material yield strength at the repad temperature. This value comes from Section II, Part D, Table Y-1. In cases where the repad temperature exceeds the highest temperature entry for this material’s yield line, the value will be zero.There are several materials that do not have clear matches in these tables. When a clear match cannot be found by the software’s assignment criteria, the software will calculate the yield strength using the external pressure chart and the method described in UG-28(c)(2) Step 3. This is more common with non-ferrous materials. If no match is found and the software cannot perform the described calculation, this value will be zero. Manually editing this field will inform the software that the user is defining the material differently than what is stored in the database and the connection to the material in the database will be severed. This is indicated by the “Unlisted Material” caption.

Related articles

Page:

Attaching Structural Elements
Page:

Leg Supports for Vertical Vessels
Page:

Component Order Troubleshooting
Page:

Leg - Repad Information
Page:

Leg - Leg Information

Browser not supported