DesignCalcs 2017.2 Release Notes (Release Candidate)

New Features

ASME Section VIII, Division 2 calculations will start are being rolled out over the next several releases.
Section VIII, Division 2 calculations for hemispherical heads under internal pressure was added. DC-948
NozzlePRO integration: DesignCalcs can now launch a NozzlePRO analysis for users of the Paulin Research Group product. This initial release allows a user to spawn a NozzlePRO analysis from within the nozzle form and is limited to pressure only loads. The analysis can only be performed on nozzles attached by full penetration welds and not using the custom developed opening setting. The user can set the FE/Pipe exe path under a new tools menu. DC-1137
Tubesheet 2017 Code Change: All three tubesheet types now have a new temperature, Tfe, that represents the temperature for the flanged extension. The Tfe value sets the new allowable stress, Sfe, for the flanged extension. Sfe is based on the tubesheet material. This change was introduced in the 2017 code in Part UHX; but the software will allow you to take advantage of the change for all supported code years (2010 - 2017). When a vessel is created or patched from an older version, the Tfe value will be set to the Tts value. This will mean that any patched vessels will have an identical hr calculation (UHX-9) until Tfe is altered. Tfe only exists on the conditions grid. DC-951
Rated Flange Slip On and Socket Weld detail requirements have been added. All new designs will have the setting to perform these calculations checked by default. All data created in previous versions of DesignCalcs will have the setting to perform these calculations unchecked by default. These calculations are per UW-21 of Section VIII, Division 1. Slip On flanges will default to figure UW-21 sketch 1. Socket Weld flanges will default to sketch 4, which is the only option. The thub value, used to determine the requirements for the outer hub to host fillet leg, will default to 1/2(hub diameter - bore). Since there can be some variability in these dimensions, the field can be updated and then the requirements will update as well. DC-551
Thick Walled Expansion Joints now perform UG-79 calculations for extreme fiber elongation. DC-917

New Features - 2017 Materials Changes

There were multiple changes, additions, and deletions made to allowable stress lines, yield lines, and ultimate stress lines to cover both the 2017 Customary and Metric versions of Section II, D. These included tables 1A, 1B, 3, U, and Y-1. New relationships were made between the allowable, yield, and ultimate lines. New relationships were made between the Customary and Metric allowable stress lines. New materials were determined to need seamless equivalents and new seamless equivalent matches were determined. DC-952
The following materials are now assigned to Table UCS-23 (this includes some small typo corrections in the code book). DC-1106

SA-307 Gr A
SA-372 Gr E Cl 55, Gr F Cl 55 and 65, Gr G Cl 55 and 65, Gr H Cl 55 and 65, Gr J Cl 55
SA/EN 10028-2 13CrMo4–5
SA/EN 10216-2 P235GH, P265GH, 16Mo3, 13CrMo4–5, 10CrMo9–10

The following materials are now assigned to Table UNF-23.3 (this includes some small typo corrections in the code book). DC-1106

SB-163 N06025
SB-166 N06025
SB-167 N06025
SB-168 N06025
SB-366 N10362
SB-462 N10362
SB-516 N06025
SB-517 N06025
SB-564 N06025
SB-564 N10362
SB-574 N10362
SB-575 N10362
SB-619 N10362
SB-622 N10362
SB-626 N10362

The following materials are now assigned to Table UHA-23.3 (this includes some small typo corrections in the code book). DC-1106

SA-213 S38815
SA-240 N08904 904L
SA-240 S38815
SA-249 S38815
SA-312 S38815
SA-403 S38815
SA-479 S38815
SA-965 S30453 F304LN
SA-995 J92205 4A
SA/EN 10028-7 X2CrNi18-9
SA/EN 10028-7 X2CrNiMo17-12-2
SA/EN 10028-7 X2CrNiMoN17-11-2
SA/EN 10028-7 X2CrNiMoN17-13-3
SA/EN 10028-7 X2CrNiN18-10
SA/EN 10028-7 X5CrNiN19-9
SA/EN 10028-7 X6CrNiTi18-10

For Table UCS-23 materials, the default MDMT curve assignment for SA-299 is now B. DC-1107
For Table UCS-23 materials, the new default MDMT curve assignment of D is now in place for SA-299 Normalized. DC-1107
Made changes to the external pressure chart and table NFC-2 when using the 2017 code year for both Customary and Metric. Note that both the figure and table for NFC-2 Metric had several values that were off by as much as 1000 times at the time of publication. Note that both the figure and table for NFC-2 Metric had several values that were off by as much as 1000 times at the time of publication. The errata was reported to ASME BPV and is tracked as record 17-2339. Note that the erroneous values were never present in DesignCalcs. DC-1105
Added new external pressure charts and tables NFT-6 and HA-10 for both Customary and Metric. Note that table HA-10 Customary at 100F had several values that were off by a factor of 10 at time of publication. The errata was reported to ASME BPV and is tracked as record 17-2339. Note that the erroneous values were never present in DesignCalcs. DC-1105
New modulus of elasticity tables were added for C95800 and C95820 alloys. DC-1103
New Poisson's ratio and density assignments (Customary and Metric) were added for alloys C95800 and C95820. DC-1104
New Poisson's ratio and density assignments (Customary and Metric) were added for alloy N10362; however, this alloy is not listed in Table PRD of Section II, D. The alloy was given a default "heavy" assignment based on other NXXXX alloys. DC item not assigned
The mean coefficient of thermal expansion (MCTE) table "Other Low Alloy Steels (Group 2)" was renamed "Other Alloy Steels (Group 2)". DC-1061
Nominal compositions: Mn - 1/4 Mo, Mn - 1/2 Mo, Mn - 1/2 Mo - 1/4 Ni, Mn - 1/2 Mo - 1/2 Ni, Mn - 1/2 Mo - 3/4 Ni, Mn - V are now assigned to MCTE table "Carbon and Low Alloy Steels (Group 1)" for 2017. DC-1061
Nominal composition 18Cr - 15Ni - 4Si is now assigned to MCTE Table "Austenitic Stainless Steels (Group 3)" for all code years. DC-1061
Nominal compositions: 14Cr - 16Ni - 6Si - Cu - Mo, 18Cr - 20Ni - 5.5Si, 24Cr - 22Ni - 6Mo - 2W - Cu - N are now assigned to MCTE Table "Other Austenitic Stainless Steels (Group 4)" for all code years. DC-1061
The MCTE table "N08031" was renamed to "N08031 and N08367" and alloy N08367 is now assigned to it. DC-1061
Materials with nominal compositions 46Fe - 24Ni - 21Cr - 6Mo - N and 24Cr - 22Ni - 6Mo - 2W - Cu - N are now mapped to Material Group J in the TM tables for determining modulus of elasticity. DC-1103
Several notes changes were made for 2017 tables 1A and 1B though most were minor changes. DC-1013
Mapped the nominal composition change of 46Fe - 24Ni - 21Cr - 6Mo - Cu - N (2015) to 46Fe - 24Ni - 21Cr - 6Mo - N (2017). DC-1162
Mapped the nominal composition change of 95.2Zr + Nb (2015) to 95.5Zr + 2.5Nb (2017). DC-1162
Added the new size thickness assignment "t >= 5" from SC II, Part D Metric. DC-1174
Added the new size thickness assignment "< 3 1/8" from SC II, Part D Customary. DC item not assigned
Added the following assignments per SC II, D Metric Table 1B 2017: "0.15 - 12.67", "0.23 - 12.67", "0.43 - 12.67", "6.35 - 12.67", "50.83 to 76.20". DC-1208
Added 2017 page and line numbers to the material viewer. DC-1109

Issues Resolved

Resolved an issue for the max and min end point assignment for the size/thickness "t > 40" from Table 1A of SC II, Part D. It was assigning the max to 40 mm instead of the min. DC-1169, DC-1173
The year assignment for Table 1A notes G10, G11, G19, G28 needed to be corrected and the text of some of the notes needed to be updated. DC-1177
Corrected the min yield strength for Metric SA-182 20Cr - 18Ni - 6Mo pg 122 lines 8 and 9 to 300 MPa. DC-1179
Added missing yield ratings from 500 to 1000F for Customary Y-1 page 710 lines 25-33. DC-1175
Corrected seven Metric yield values for SB-308, T6 from SC II, D page 690, line 44. DC-1187
Corrected the missing Class/Condition/Temper value for the Metric yield line for SA-841 Gr. A; it is now correctly "1". DC-1198
Corrected the 2015 Customary min tensile value and four Customary ultimate stress values for three different aluminum materials (fifteen values were corrected). The values come from Table U of Section II, D Customary page 528, lines 7 through 9. DC-1190
Corrected the max allowed temperature from 500F to 600F for thirty five titanium allowable stress lines for both 2013 and 2015 code years. Eight R50400, nine R52400, nine R52402, and nine R52404 max temps were corrected. The 2013 values come from Table 1B of 2013 Section II, D Customary page 266, lines 2 through 9, lines 32 through 40; and page 270, lines 1 through 9, lines 19 through 27. The 2015 values come from Table 1B of 2015 Section II, D Customary page 258, lines 25 through 32; page 262 lines 11 through 19, lines 25 through 33; page 266, lines 1 through 9. DC-1190
Corrected the max allowed temperature from 260C to 316C for thirty five titanium allowable stress lines for both 2013 and 2015 code years. Eight R50400, nine R52400, nine R52402, and nine R52404 max temps were corrected. The 2013 values come from Table 1B of 2013 Section II, D Metric page 266, lines 2 through 9, lines 32 through 40; and page 270, lines 1 through 9, lines 19 through 27. The 2015 values come from Table 1B of 2015 Section II, D Metric page 258, lines 25 through 32; page 262 lines 11 through 19, lines 25 through 33; page 266, lines 1 through 9. DC-1207
Corrected the product form for Table U Customary 2015 pg. 520, line 16 to say "pipe" instead of "tube". DC-1207
Corrected the min tensile for Table U Customary 2015 pg. 490, line 19 from 75400 psi to 75500 psi. DC-1207
Corrected the size/thickness from 0.250 - 5.000 to 0.010 - 0.249 for pg. 528 ln 10 Table U Customary 2015. DC-1207
Corrected the product form for the 2015 Metric yield lines on page 690, line 32 and 33 of Metric SC II, D. They are now correctly "Bar, Rod, Wire". DC-1200
Corrected the min tensile strength for pg 598, line 17 from 66500 psi to 65500 psi for Table Y-1 Customary 2015. DC-1207
Corrected the 2015 U Customary size/thickness, min tensile, and utlimate stress values for SB-209 Alclad 6061 pg 528, lines 7, 8, 9. DC-1216
Corrected an issue that was preventing the 2017 Yield and Ultimate page and line numbers from showing in the material viewer. DC-1237
Corrected an issue in the Studded Outlet report where the weld detail calculations for the new condition tmin value, was showing the wrong value for the host t. This did not affect the result at all. DC-1314
Corrected an issue that sometimes showed a false failing message for UG-45 nozzle calculations in the report. The problem was in the pipe min wall calculation, the result was truncated in certain cases instead of rounded for the displayed message. DC-1003

Miscellaneous

Google Analytics has been added to DesignCalcs. DC-1269
The default code year for new vessels is now 2017. DC-958
Several materials had inconsistent spacing in their nominal compositions for "1Cr - 1/2 Mo", "1Cr - 1Mn - 1/4 Mo", "2 1/4Cr - 1Mo" to "2 1/4 Cr - 1Mo". This has been standardized. DC-1197
Standardized the product form for "Condenser tube, Heat exchnager tube". Some places had it as "...tubes,...tubes". DC-1200
Standardized the class/condition/temper of "Hot worked or Cold worked ann." for Table U Customary. DC-1207
Streamlined "SA/NF A36-215" to "SA/NF A 36-215" in several places in the Y-1 and U tables. DC-1216
The about screen was updated to say "through 2017 Edition". DC-956
Selecting the 2017 code year no longer requires a confirm from the user or makes a statement about the year being in active development. DC-1267